The Diamond Butterfly Valve is a hygienic, in-line, 1/4 turn or multi-position unit for manual and actuated service.

Maximum Operating Pressure: 10 Bar. Working Temperature dependent on seal materials range -10°C up to 150°C. Valves can be supplied to operate outside these parameters – please enquire.

For other combinations, contact DPL.

Actuation and Control
Butterfly valves can be supplied fitted and tested with a comprehensive range of pneumatic and electric actuators including all ancilliary equipment such as solenoids, limit switches and positioners.

ATEX approved version available for use in potentially explosive atmospheres.

Group 2, Category 2, Gas and dust compliant

  • Fully machined from 316L forgings for a high quality, non porous construction.

  • Polished, crevice free disc which is easily cleaned.

  • ‘0’ ring spindle is environmentally sealed.

  • Spindle bearings fit into seal cross holes resulting in low torque.

  • Range of seal materials available including EPDM, Silicone, Viton steam resistant and Nitrile to suit your application.
     

Valve Dimension ‘A’

FITTING TYPE DIMENSION ‘A’ mm
  1.0” – 3.0” 4.0”
RJT MALE 80 90
FEMALE 85 125
IDF MALE 80 100
FEMALE 102 160
ILC MALE 80 100
FEMALE 102 142
CLAMP 60 100
BUTT WELD ENDS 60 100
MANUAL FLANGED 260 260
ACTUATED FLANGED 140 140

Other Dimensions

Size 1.0” 1.5” 2.0” 2.5” 3.0” 4.0”
B mm 90 94 101 107 113 129
C mm 39.5 43.5 50.5 57 63 79
Dia. D mm 102 102 102 102 102 102
E mm 251 255 262 268 275 291
F mm 160 160 160 160 160 160

THE FINER DETAILS...

Diamond Butterfly Valves

The Diamond Butterfly Valve is a hygienic, in-line, 1/4 turn or multi-position unit for manual and actuated service.

Maximum Operating Pressure: 10 Bar. Working Temperature dependent on seal materials range -10°C up to 150°C. Valves can be supplied to operate outside these parameters - please enquire.

For other combinations, contact DPL.

Actuation and Control
Butterfly valves can be supplied fitted and tested with a comprehensive range of pneumatic and electric actuators including all ancilliary equipment such as solenoids, limit switches and positioners.

ATEX approved version available for use in potentially explosive atmospheres.

Group 2, Category 2, Gas and dust compliant

DOWNLOAD CATALOGUE

Download the catalogue by simply completing your details below

DOWNLOAD CATALOGUE WITH SELECT

Name
Name

Certification

Certification for DPL Products

From the vast array of published standards there are a number that are key to each industry. The accepted way of confirming that the standard has been complied with is for the manufacturer or service provider to issue a form of certificate with the goods or service.

There are many types of certificate but typically they can be categorised as Certificates of compliance, Test certificates, Inspection certificates or reports and Certificates of acquired skill or attainment.

DPL is an assessed company to the ISO 9001:2015 Quality Assurance standard and certifies that its products meet the relevant standards the product was designed for and also where modifications are made to suit a specific purpose.   We provide a Certificate of Conformance with each order dispatched.   Our seal and gasket components are food contact safe and we provide certification for these that states the relevant FDA schedule number for the material.

Valve Test Certificate is available for all DPL supplied valves.   This will supply information on the materials used, the seal material and seal standards, the method of test and the test pressures, and the internal surface finish.   Component Material certificates for the product wetted surfaces of the valve are also available with this certificate.

EU safety law

A statement of compliance is normally a legal requirement evoked by a European Directive.   DPL issue these with every valve and actuator in line with the requirements of the particular commodity type along with our recommended valve installation procedures.

Some of the legislation affecting DPL products includes the Pressure Equipment Directive (PED), designed for pressure bearing products safety and the Machinery Directive that requires the design of the machinery is safe to operate and presents no hazard in operation.

DPL produces valves that comply with the electrical bias ATEX directive, for safety of operation in potentially explosive atmospheres which also seeks to prevent ignition through static discharge on non electrical products.

There are many other specialist certificates that have not been covered above.   If you require a particular approval certificate for the components we can supply for your installation please enquire at the time of order with your DPL Sales contact.

Quality

Stainless Fittings (SFL) and Dairy Pipe Lines (DPL) are manufacturers of a range of stainless steel fittings, valves and bespoke fabricated units for the bio-processing, pharmaceutical and food industries. The companies are regularly assessed to the ISO 9001:2015 Quality Management standard.

The products provided by the company meet the stringent statutory and regulatory requirements demanded by the marketplace.  Inspections and product tests are carried out at regular stages of manufacture allowing comprehensive quality records to be maintained. These records can then be used for analysis as part of our commitment to ongoing process and product improvements. As part of this process, bi-monthly reviews are in place to ensure the quality system continues to support our business objectives.

With the processes of the Quality Management System defined and implemented, one major role of the management team is to adapt these processes to meet changing requirements in the industry and to enhance the business wherever this results in a benefit to our customers.

Our initial contact with our customers is normally through the Sales team. Here your precise requirements are assessed and stock availability discussed with you in order to meet your needs. Where you require us to make use of our fabrication facility, we take the time to understand your exact requirements even further.
After being sure that your sales contact has a clear understanding of your requirements, we conduct a Contract Review Meeting to ensure that the entire team responsible for manufacturing your order are all clear on what is needed.
We will contact you where we need further information or where we need specific points being clarified. All agreements are documented so you can be sure we have your requirements on board.

Material traceability is of prime importance to us, and therefore our internal bespoke systems and material identification allows us to trace material back to its origin.

SFL and DPL offer a wide range of certification options to include Certificates of Conformance, Original Material Certificates, EP or Passivation Certs, Weld maps, Qualifications and Procedures to name a few. Just discuss your requirements with us – our Mission is your Peace of Mind.

Click one of these links to view or download our EU Directive Statements for

Enquiry / CAD Request DPL

Address(Required)

OUR CUSTOMER’S THOUGHTS...